Our IncredaFILL Tub (70gm) is your Go-To Solution for Small Repairs, Touch-Ups, and quick fixes! Designed as a urethane polymer filler, IncredaFILL® is ready-mixed and cures under UV light in the blink of an eye. Just a mere 5-second exposure to an LED 405nm UV torch, and you’re all set—it’s ready for sanding and painting. The IncredaFILL Tub is designed to be 100% solid in paste and cured forms, ensuring a non-shrinking, non-cracking finish. Sand it easily and finish with any paint or varnish you choose. Experience the power and convenience of IncredaFILL™ in a smaller, even more accessible tub.
Includes:
1 x 70grams IncredaFILL® filler paste
Don’t waste valuable time waiting for your filler to dry…Buy IncredaFILL® today and get the job done FAST.
APPLICATION INSTRUCTIONS
Be sure to wear proper safety gear when working with IncredaFILL™ and sanding the cured material. Always try to avoid breathing in the fumes, filler particles or dust.
Prepare the surface with some light sanding (if needed). Using a slightly damp rag, wipe the area to remove dust and other contaminates.
Always work indoors and away from any UV light. Unscrew the lid to reveal the Safety seal (this is to prevent the product from accidental UV exposure. Remove the seal to expose the product.
Using a flexible metal or plastic applicator, scoop out a small amount of IncredaFILL™ from the Tub. We recommend testing a small batch before using it on your actual project.
Apply the paste in thin layers to the surface on which you are working. The smoother you can get it at this stage, the easier it will be when sanding.
Pro Tip: To save time with sanding, be sure not to overfill.
Once the treated area is smooth and ready, use a 395-405nm UV light source to start the curing process. To do this, expose the material to UV light for 15-20 seconds. Hold the light over the uncured material for larger areas and use a zig-zag pattern to expose a section at a time. Alternatively, you could place the object in direct sunlight to cure large areas quickly.
Pro Tip: For deeper holes, to ensure the product is adequately cured, apply and cure in thin layers to build it up.
Once IncredaFILL™ has been appropriately cured, wipe the surface with Isopropyl Alcohol (IPA). Wiping removes any excess material that might remain on the surface.
Starting with coarse grade sandpaper (60-100 Grit), remove the excess filler. To ensure a smooth finish, step up the sandpaper grades, e.g. 80, 120, 240, 400, 800.
Pro Tip – Unlike some fillers, IncredaFILL™ can be wet sanded. Using wet sandpaper helps keep the dust particles down and keeps it cleaner and less likely to gum up.
After reaching the desired smoothness, prepare the surface by wiping it with a “tack rag” to remove the dust left from sanding. Apply a good quality Paint Primer, and apply to the surface.
After the primer has dried, the topcoat can be applied (unless further sanding is required)
Pro Tip – To achieve the smoothest results, repeat the priming and wet sanding process.
PHYSICAL PROPERTIES
Colour(s) – Semi-Transparent Grey
Viscosity – 70,000cps
Odour – Negligible Characteristics
Shelf Life – 36 months
UV Cure – 395nm to 405nm
Cure Speed – 15 Seconds with UV LED Torch
Storage – Store in a dark, cool, dry place away from direct sunlight.
Wash Up – RESINAWAY® & IPA
MECHANICAL PROPERTIES
Max Force (kN) 1.54
Tensile Strength (MPa) 51
Percentage Elongation at Break 2.5
Young’s Modulus (GPa) 0.7
Shore Hardness (Scale D) 94.5
Temp. Resistance (C) -20 to 60*C
Max Load Applied (N) 160
Flexural Stress (MPa) 143
Max Flexural Strain (mm/mm) 0.05
Method Code ASTM D790-10
