These bands offer an inexpensive yet durable means of holding sections of moulds together. Made of high quality rubber, they can withstand heat up to 120 degrees Celsius.
Open weave mould making cloth, used for reinforcing plaster moulds and plaster statues. Preferred by some professionals over hemp fibres.
Made of 100% Nylon strapping with locked metal fasteners. Used to band most sizes and shapes of moulds for a tighter fit. All mould straps are 1 inch in width
Regular casting plaster used for quick casts into alginate or latex moulds.
Hydrocal 105 is a good strong mould material. Commonly known as buff stone, an off colored stone ideal for sculpting prosthetics. For dental stones with controlled expansion
Hydrostone TB is one of the hardest and strongest gypsum cements. Slightly higher setting expansion than hydrocal, but is ideal in case moulds, press and stretch dies. The most widely used product for solid casts and statuary.
USG Pottery plaster is highly uniform, noted for outstanding performance and long life. Ideal for running slip latex, sanitaryware and dinnerware.
Regular Dental Plaster is used as a quick setting, fine casting plaster. This plaster is grit free with a short setting time.
Ultracal 30 is the most widely used gypsum cement with the lowest expansion rate available. The industry standard for casting of foam latex. Highest strength with less tendency to warp. Excellent for case moulds, close tolerance tooling and applications requiring exceptional hardness.
White Hydrocal is a gypsum product used for slip latex moulds and case moulds. Offers slightly better heat resistance than pottery plaster with higher wet and dry strengths.
Challenge 95 is primarily a release for flexible and rigid polyurethane elastomers and foams. It can be used for other polyurethane systems as well, however, it is advisable to test prior to its use. Challenge 95 is a universal release for plaster, metal, urethane, and epoxy molds.
Stoner E236 Urethane Mold Release is specially formulated as a release agent and anti-stick lubricant for molded urethanes. A light coating produces best results.
Stoner E302 Rocket Release is an extremely versatile release agent which is generally acceptable for applications where a food grade release is required. In many applications, Rocket Release is considered to be the most paintable release agent available when molding plastics and similar materials.
Stoner A324 Rapid Release is specially formulated to release molded silicone rubber, thermoset plastics, rubber, and similar materials. It provides a long lasting, thin-layer of anti-stick coating for fast, easy part removal from metal, plastic, rubber, and even silicone rubber molds.
Water based release. An emulsion of silicone oils and resins. When used with a spray applicator, it is an economical alternative to aerosol release agents. The use of a soft brush to distribute the release agent evenly may improve results. Primary use is for polyurethane and latex moulds when casting cement based products.
Classed as a general purpose release agent, however it far surpasses most release systems on the market. Designed for use at moderate temperatures where a silicone release is not desired. It provides a matte finish when applied and can also be polished when applied to rigid surfaces. J-WAX is perfect to PU-PU moulding.
Mirror Glaze No.8 is a blend of waxes specially formulated to provide the maximum number of releases per application. Especially useful on tooling and new moulds.
This is a versatile lubricant for use as a mould separator. It can be used full strength or diluted with water. Most popular for plaster and gypsum moulds.
A special formula release agent for the fiberglass industry. This product is designed to prevent lamination of the product to the mould. Preventing the mechanical or chemical bonding of the molded material to the surface of the mould. PVA is a film-forming solution, which places a positive barrier between the mould and the product or component.
For use with Barnes resin moulds.
Water based dental separator. Used in dental acrylic processes and for floating off multiple appliance sculptures when sculpting on plaster and white hydrocal.
This material allows the user to laminate fibreglass moulds directly onto wet clay. The vinyl spray is applied to the clay surface as a barrier coat to seal in any moisture from the clay sculpt or walls. Use in conjunction with a suitable release agent such as J-Wax. The Vinyl Spray also imparts some protective properties to the sculpt while the moulds...
Hydrocal® 106 is a white dental stone. This product incorporates quickly and has a high strength within one hour after set.
Nitrile gloves making them suitable for people with allergies to natural rubber latex. Stronger than standard latex or vinyl disposable gloves. Offer superior flexibility and touch.